Logo

P3988 Engine Trouble Code

P3988 Engine

When you check engine light came on code P3988 the reason should be . However your vehicle's manufacturer may have a different definition for the P3988 OBD-II Diagnostic Powertrain (P) Trouble Code. So you should chech it on our car models.

When the DTC check engine light comes P3988 code on the first you can check is the gas related maybe gas cap. Pull over, retighten it, and take a look at the cap to see if it has any cracks inside. Go on driving and to see if the check engine light turns off automaticly. On the other hand, you can buy a gas cap for about $4.5 at an auto parts store. All you need to do is take the old one take off and take on the new one. If you've already bought it to the store, you might as well just replace the cap. While not car-threatening, it's good to take care of this right away to improve gas mileage/km.

P3988 Code Meaning :

P
OBD-II Diagnostic Powertrain (P) Trouble Code For Engine
3
Ignition System Or Misfire
9
Fuel Rail/System Pressure - Too High
8
Cylinder 1 Injector Circuit Low
8
Timing Reference High Resolution Signal A Too Many Pulses

The oxygen (02) sensors on your car measure the oxygen in the exhaust to determine how rich or lean the ratio of fuel and air are in the cylinders. Optimizing this mixture means better fuel economy and fewer exhaust emissions.

P3988 OBD-II Diagnostic Powertrain (P) Trouble Code Description

P3988 engine trouble code is about Timing Reference High Resolution Signal A Too Many Pulses. Fuel Rail/System Pressure - Too High and Cylinder 1 Injector Circuit Low causes most of code P3988.

Reason For P3988 Code

The reason of P3988 OBD-II Engine Trouble Code is Fuel Rail/System Pressure - Too High.

P3988 DTC specifically refers to the camshaft (cam) timing. In this case, if the cam timing is over-retarded, the engine trouble light will be illluminated and the code will be set.

How To Repair P3988 Code

Before starting let's see P3988 repairing process steps:

  • Qualified technicians will begin by using a scan tool to access P3988 code stored in the ECU.
  • Technicians will note P3988 code present and any freeze frame data associated with them.
  • After all, if you sure the engine trouble is finished, the code will be cleared.

A faulty ECM could result in the vehicle to be dealing with a reduction in fuel efficiency, power, and acceleration. A vehicle that fails to start or struggles to start is another main symptom or a defective or failed ECM. If the ECM fails completely, the vehicle will remain with no engine control management, and will not be starting or running as a result.

If you suspect that your car has a defective mass air flow sensor, bring it to a certified mechanic so that a whole computer diagnostic can be run. In most situations, a defective mass flow sensor has a certain code that will process throughout computer diagnostics, and is normally simple to check into with computer testing equipment.

Sometimes P3988 code comes with P398800 code.

Diagnosis Of Engine Error OBD Code P3988

It's essential to diagnose this trouble code. Then are some way which a handyperson should follow for diagnosing the problem that started a P3988 trouble code to be stored

The first step is introductory and is about reacquiring all the canons that have been set. For this, the individual scanner will have to be plugged into the individual harborage of your vehicle. Make sure you indurate frame the data. Any canons that were set previous to the P3988 code will have to be sorted first, as they may have been the reason for the law to set in the first place. It's always good to rule that out.

The coming step is to run a introductory examination of all the electrical circuits, connectors, wiring etc for damages similar as becks, erosion, fraudulent legs etc. All of these will have to be repaired or replaced. After that's sorted, clear the canons and go on a test drive to see if it resets. In case it resets, you'll have to continue your opinion. Depending on your vehicle you may have a vacuum operated selector or a vacuum solenoid if it's electrically actuated. In the case of the former, a hand held vacuum pump will have to be used to testit.The purpose is to see if the internal stopcock is getting turned by the selector, motor or solenoid. In order to do this, a command can be transferred to the system with scanner or by driving the vehicle under the special conditions that will spark the system. While this is passing keep an eye on the checkup tool data for the result.

All Engine Trouble Codes

All engine trouble codes with P, U, B and C engine codes.

Code Search

Please fill the "Code Box" to find engine fault code.

Example: 0140

Car Models :

Please select your car.

How To Read Engine Codes ?

Ways to read engine trouble codes.

How To Clear Check Engine Lights ?

Ways to clear check engine light on car panel.

Check Engine Light Dictionary

Ways to clear check engine light on car panel.